- #Saffire mixcontrol audio through one ear how to
- #Saffire mixcontrol audio through one ear Patch
- #Saffire mixcontrol audio through one ear full
- #Saffire mixcontrol audio through one ear pro
- #Saffire mixcontrol audio through one ear software
#Saffire mixcontrol audio through one ear software
Perhaps i made a mistake but i wrote this without access to the software Route this mix to headphones and your vocals will have eq applied to it. I see your mixing your inputs so if you set your routing as followed :Īnalog in 3 is eq in and set this also as track in the software mixer.
#Saffire mixcontrol audio through one ear how to
The thing is how to get the send to the eq. Say fader one to 10 set to the daw and fader 11 to input of eq and send that software mixer mix to headphones itshould work with almost no latency. If you make a headphone mix within the mixer I work with a scarlett 18i20 and a octopre where in some setups the scarlett are my inputs and outputs and the octopre my insert points ( send / return). It is possible but you have to remember that latency will happen.ītw this software is not the best thing for inserts but it can be done. Now while playing send track to 3/4 and monitor it on example 1/2. Have a channel say vocal set through output 3/4.Ĭonnect eq to output 3/4 and let it back in on 3/4. However if you route a channel through the eq and let it back in to the daw and send that to the main it will be presented through the headphones. Next thing i see you headphones are set to daw 3 and 4 which basicly means they will never present your outboard equipment. That means your outputs presenting the sound of your daw. Really appreciate any help or ideas you could throw my way.įirst thing i noticed is the interface is in daw mode.
Whenever I seem to monitor through the headphones I just get what I believe is the dry signal from Logic with no additional EQ or compression.Īlso, I've noticed that on headphone mix 2 it only seems to be outputting from the left hand side? Not sure If I've done something wrong or the unit is faulty. Is there a better way of patching than I have done or is this simply no possible? I'd prefer not to run the EQ into the compressor for obvious reasons.
#Saffire mixcontrol audio through one ear Patch
I don't mind changing the Saffire Mix control routing to make this possible (e.g - changing my saved mix "profiles" to switch between output from monitors to headphones and then back) but what I don't want to have to do is have to unplug the patch cables every time to make this a possibility. I work on a mixture of monitors and headphones so would prefer to be able to hear the eq & compression through both when I need to. But I can't seem to work out how to monitor the changes through headphones.
I can monitor the addition of the EQ and Compression through my monitors when playing back in logic. I manged to patch them in accordingly from outputs 3/4 back into 3/4, and also out of 5/6 and back into 5/6.
#Saffire mixcontrol audio through one ear pro
I've recently upgraded to a Saffire Pro 26 as I was given a TLA 5013 stereo EQ and a DBX266XL stereo compressor by a friend. The H/W Control button (Saffire PRO 40, Liquid Saffire 56 and Scarlett 18i20 only) links the position of the monitor dial in the MixControl software to the position of the monitor level control on the front of the Saffire hardware.Firstly, I'm currently using I'm currently using Logic 9.1.8 and also the Saffire Mix Control software. However, all of these presets can be configured manually using the method described above. The Monitor Preset… button allows you to select a variety of preset speaker configurations, more information about which can be found on your product’s download's page. Care should be exercised so as not to damage any audio equipment connected to these outputs, as the audio will be very loudĬlicking on the individual outputs toggles them between blue and red, whereas holding down the SHIFT button on your keyboard and clicking will turn the output grey/silver.
#Saffire mixcontrol audio through one ear full
Grey/Silver outputs are active and will output any audio at full volume, regardless of the position of the monitor level dial.Blue outputs are active, and their level is controlled by the monitor level dial in the MixControl software (shown in the screenshot above).Red outputs are muted, and no audio will be passed from them.They will either beRed, Blue, or Grey/Silver. This is achieved in the monitor section of MixControl, shown below:Ībove the Monitor Preset… button in the monitoring section of Saffire MixControl, you will be able to see numbered boxes corresponding to the line (analogue) outputs on your unit. Once you have configured your mixes and routed audio to the outputs of your Saffire (see Part I and Part II of this tutorial), you need to ensure that a sufficient level is getting to your chosen outputs. Applies to: Saffire Range and 1st Generation Scarlett 6i6, 8i6, 18i6, 18i8 and 18i20
0 kommentar(er)
